Miller Millermatic 350P Bedienungshandbuch Seite 38
- Seite / 72
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
OM-1327 Page 34
5-5. Setting Crater Fill
To set Crater Fill, select a program and
press SETUP (1) until the TIMERS LED
turns on. Press SETUP again and the left
display will show CRTR and the right display
will show OFF.
Rotate right knob (3) to turn crater ON.
Rotate left knob (2) to change display to
WFS, and rotate right knob (3) to set crater
wire feed speed. Wire feed speed range is
50-700 IPM (see Section 4-10).
Rotate left knob (2) to change display to
TIME, and rotate right knob (3) to set crater
time. Time range is 0.1-5.0 seconds (see
Section 4-10).
Rotate left knob (2) to change display to
VOLT (MIG program) or ARCL (pulse
program), and rotate right knob (3) to set
either volts (range is 10.0-32.0 volts) or arc
length [range is 0-99 (see Section 4-10)].
Rotate left knob (2) to change display to
TDLY for time delay. This setting is for spot
or skip welding without crater fill if the arc
time is less than the set time. Time range is
0.0-5.0 seconds (i.e. if TDLY is set for 2.0
seconds, weld operation will not go into
crater if gun trigger is released before 2.0
seconds).
To exit this menu, press the SETUP (1)
button.
Ref. 213 935-A
3
1
. Crater parameters are welding gun independent (i.e. crater fill can be on for a
spool gun and off for a MIG gun). When using the same welding gun, MIG and pulse
programs are independent of each other; however, crater parameters will be the
same for all pulse programs. For example, if a MIG gun is using the .035 steel pulse
program, and crater fill is on and parameters are set, crater will also be on and the
same parameters will be set for a stainless pulse program.
2
- Millermatic 350 And 1
- Millermatic 350P 1
- From Miller to You 2
- TABLE OF CONTENTS 3
- 1-1. Symbol Usage 5
- 1-2. Arc Welding Hazards 5
- can affect pacemakers 6
- 1-6. EMF Information 8
- 2-1. Symboles utilisés 9
- LES CHARGES ÉLECTROSTATIQUES 11
- 2-6. Information EMF 12
- SECTION 3 − INSTALLATION 13
- 3-3. Volt-Ampere Curve 14
- 3-5. Installing Work Clamp 15
- 3-7. Installing Welding Gun 16
- 803 568-C 17
- . Be sure to trim liner to 18
- Changing Polarity 19
- 3-11. Installing Gas Supply 20
- . Check input voltage 22
- . Incorrect linking can 22
- Ref. 803 543-C / 803 766-A 23
- . Hold wire tightly to 25
- . Use pressure indi 25
- . Use pressure indicator 26
- SECTION 4 − OPERATION 28
- OM-1327 Page 25 29
- WELDCHARTS 30
- Gas WireMaterial 30
- OM-1327 Page 27 31
- Recommended Crater Parameters 32
- 19ga. 20ga 33
- (1.05mm) 33
- SECTION 5 − PROGRAMMING 34
- 5-2. Pulse MIG Welding Mode 35
- 5-3. Timers 36
- CRTR appears in the left 37
- 5-5. Setting Crater Fill 38
- ALST appears in 39
- 5-7. System Reset 40
- . Maintain more often 41
- 221 044-A / Ref. 803 550-A 42
- . The drive assembly comes 43
- . U-Grooved drive rolls are 43
- 6-5. Troubleshooting 44
- OM-1327 Page 41 45
- SC-187 212-A 46
- OM-1327 Page 43 47
- OM-1327 Page 44 48
- OM-1327 Page 45 49
- OM-1327 Page 46 50
- OM-1327 Page 47 51
- SECTION 8 − PARTS LIST 52
- OM-1327 Page 49 53
- . Hardware is common and 54
- OM-1327 Page 51 55
- OM-1327 Page 53 57
- Ref. S-0025-D 61
- 1 2 3 4 5,7 62
- OM-1327 Page 59 63
- OM-1327 Page 60 64
- OM-1327 Page 61 65
- Figure 8-8. 4012 Gun 66
- OM-1327 Page 63 67
- Effective January 1, 2005 71
- For Service 72
- Owner’s Record 72
Verwandte Produkte und Handbücher für Schweißsystem Miller Millermatic 350P
Schweißsystem Miller MTT-2512WV Spezifikationen
(12 Seiten)
(12 Seiten)
Schweißsystem Miller CE Spezifikationen
(64 Seiten)
(64 Seiten)
(68 Seiten)
Schweißsystem Miller GA-17C Spezifikationen
(25 Seiten)
(25 Seiten)
Schweißsystem Miller System 9A Spezifikationen
(52 Seiten)
(52 Seiten)
Schweißsystem Miller GA-17C Bedienungshandbuch
(12 Seiten)
(12 Seiten)
Schweißsystem Miller System 9A Spezifikationen
(80 Seiten)
(80 Seiten)
Schweißsystem Miller 1020 Bedienungshandbuch
(36 Seiten)
(36 Seiten)
Schweißsystem Miller PipeWorx 400 Bedienungshandbuch
(116 Seiten)
(116 Seiten)
Schweißsystem Miller RPC-IP Bedienungsanleitung
(20 Seiten)
(20 Seiten)
Bendix-commercial-vehicle-systems FRICTION MATERIALS manuály
Uživatelské manuály a uživatelské příručky pro Zařízení Bendix-commercial-vehicle-systems FRICTION MATERIALS.
Poskytujeme 1 manuály pdf Bendix-commercial-vehicle-systems FRICTION MATERIALS ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Kommentare zu diesen Handbüchern